AjapaReporter

Home life · Updated

How to Descale Breville Barista Express

Time it takes30 min
Steps9in the list below
LevelMediumsome care needed
Official sourceBrevillecheck it for changes

Quick answer Descaling removes mineral buildup inside your Breville Barista Express, keeping water flow and heating consistent. Run the machine's built-in descale cycle with a food-safe descaling solution, then rinse thoroughly.

What You’ll Need

  • Breville descaling solution (or a food-safe citric acid descaler)
  • Fresh water for rinsing
  • Empty container or jug (at least 2 liters capacity)
  • Cleaning brush or cloth (for wiping exterior)

Step-by-Step

  1. Prepare the machine: Turn off the machine and unplug it. Remove the water filter (if installed) and set it aside. Take out the drip tray and empty it, then replace it.
  2. Fill the reservoir with descaling solution: Follow the solution’s instructions for the correct ratio (typically one part solution to two parts water). Pour the mixture into the water tank and place it back.
  3. Enter descale mode: Plug the machine in and turn it on. Press and hold the 1-Cup and 2-Cup buttons simultaneously for about 5 seconds until the lights blink. The machine is now in descale mode.
  4. Start the descaling cycle: Press the 1-Cup button to begin. The machine will pump the solution through the group head and steam wand in intervals. Place a large container under the group head and steam wand to catch the liquid.
  5. Let the cycle run: The machine will pause periodically. When it stops, empty the container and reposition it. Press 1-Cup again to continue. Repeat until the tank is empty (the machine will beep).
  6. Rinse the reservoir: Remove the tank, rinse it thoroughly, and fill it with fresh water. Replace it.
  7. Run a rinse cycle: Press the 1-Cup button to pump fresh water through the machine. Let it run until the tank is empty. You may need to do this twice to remove all solution residue.
  8. Flush the steam wand: Turn the steam dial on to let hot water/steam flush through the wand for about 30 seconds. Turn it off.
  9. Exit descale mode and clean up: Press and hold the 1-Cup and 2-Cup buttons again for 5 seconds to exit descale mode. Wipe down the exterior, replace the water filter, and empty the drip tray.

Common Mistakes

  • Skipping the rinse cycle: Not rinsing thoroughly leaves descaling solution in the boiler, which can affect taste and potentially irritate your stomach. Always run at least two full rinse cycles.
  • Using vinegar: Vinegar is not recommended because its acidity can damage internal seals and leave a lingering odor. Use a proper descaling solution.
  • Forgetting to remove the water filter: The filter can absorb the descaling solution, making it unusable and reducing its effectiveness.
  • Not placing a container under the steam wand: The cycle flushes through the wand, so you need to catch the liquid there too, or you’ll have a mess.
  • Interrupting the cycle: Let the machine complete its sequence. Stopping mid-cycle can leave solution in the boiler.

Tips

  • Descale every 3-6 months, depending on water hardness and usage. If you notice slower brewing or louder heating, it’s time to descale.
  • Use filtered or softened water to reduce mineral buildup.
  • Check your machine’s manual for specific descale instructions, as menu paths may differ slightly by model.
  • Keep the drip tray and steam wand clean between descaling to maintain performance.
  • If you use a third-party descaler, make sure it’s labeled as safe for espresso machines.

Troubleshooting

  • Machine doesn’t enter descale mode: Ensure the machine is off before holding the buttons. If it still doesn’t work, unplug for 30 seconds and try again. Some models require a different button combination—check your manual.
  • Water not flowing during rinse: Check that the tank is seated properly and the water level is sufficient. If the machine is still hot, wait for it to cool slightly.
  • Descale cycle stops early: The machine may pause to let the solution soak. Wait a few minutes—it should resume automatically. If it doesn’t, press the 1-Cup button to continue.
  • Residual taste after rinsing: Run another rinse cycle with fresh water. If the taste persists, repeat the rinse process.
  • Error lights after descaling: Turn off the machine, unplug for a minute, then plug back in. If the error persists, contact Breville support.

Frequently Asked Questions

How often should I descale my Breville Barista Express?

Every 3-6 months, or when the machine signals it’s time (if your model has a descale indicator). Hard water may require more frequent descaling.

Can I use vinegar instead of descaling solution?

It’s not recommended. Vinegar can damage internal components and leave a bad taste. Use a commercial descaling solution designed for espresso machines.

Do I need to remove the water filter before descaling?

Yes, always remove the water filter. The descaling solution can clog or damage it, and the filter may absorb solution, reducing its effectiveness.

What if I don’t descale my machine?

Mineral buildup can clog the boiler and pipes, leading to slower brewing, poor extraction, and eventually machine failure. Regular descaling extends the life of your machine.

Can I descale with the steam wand?

Yes, the descale cycle flushes through both the group head and the steam wand. That’s why you need a container to catch the liquid from both.

How do I know when descaling is complete?

The machine will beep and return to normal operation mode. You’ll also notice the tank is empty and the rinse cycles have finished.

Sources: Breville. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.