AjapaReporter

Home life · Updated

How to Descale Your Keurig with Vinegar

Time it takes45 min
Steps8in the list below
LevelEasyno special skills
Official sourceKeurig Supportcheck it for changes

Quick answer Descaling your Keurig with vinegar removes mineral buildup that slows brewing and affects taste. Run a vinegar solution through the machine, then rinse with water.

Over time, minerals from water collect inside your Keurig and can clog the internal lines, making brewing slower and coffee taste off. A vinegar descale is the cheapest and most effective way to clean it. You only need white vinegar and water, plus a mug or carafe. Do this every 3–6 months, or sooner if you notice slow brewing or odd flavors.

What You’ll Need

  • White vinegar (plain, not diluted)
  • Fresh water
  • A large mug or carafe (at least 12 oz)
  • A sink or large bowl for rinsing the reservoir
  • Paper towels or a cloth for wiping

Step-by-Step

  1. Unplug and remove parts. Unplug the Keurig. Remove the water reservoir, the drip tray, and the K-cup holder. Wash these in warm soapy water, rinse, and dry. Leave them off for now.
  2. Mix the descaling solution. Fill the water reservoir halfway with white vinegar, then fill the rest with water. Use equal parts vinegar and water. For a standard 48 oz reservoir, that’s about 24 oz of each. If your machine has a smaller reservoir, adjust accordingly.
  3. Place a large mug or carafe on the drip tray. Make sure it can hold at least 12 oz, because the machine will dispense that much liquid.
  4. Run a brew cycle without a K-cup. Plug the machine back in, turn it on, and lift the handle. Do not insert a K-cup. Place the mug under the spout, select the largest cup size (usually 10 or 12 oz), and press brew. The vinegar solution will run through the internal lines.
  5. Repeat until the reservoir is empty. After the first brew, empty the mug and repeat the brew cycle. Keep going until the reservoir is empty. This forces the vinegar through all the internal parts.
  6. Let it sit for 30 minutes. After the last brew, leave the machine on but do not use it. The vinegar needs time to dissolve scale inside. Set a timer for 30 minutes.
  7. Rinse the reservoir and refill with fresh water. Empty any remaining vinegar from the reservoir, wash it thoroughly with soap and water, and rinse well. Refill with fresh, cold water.
  8. Run 2–3 water-only brew cycles. Place the mug back, and brew water only (no K-cup) on the largest size. Empty the mug after each cycle. Repeat 2–3 times to flush out any vinegar taste. If you still smell vinegar, run one more cycle.

Common Mistakes

  • Skipping the soak. The 30-minute wait is essential. Without it, vinegar doesn’t have time to dissolve scale inside the machine.
  • Using too little vinegar. A weak solution won’t clean effectively. Stick to a 1:1 ratio.
  • Not rinsing enough. If you don’t run enough water cycles, your coffee will taste like vinegar. Always do at least 2–3 rinses.
  • Brewing with a K-cup during descaling. This wastes a pod and can push scale into the needle. Always descale without a pod.
  • Forgetting to remove the water filter. If your Keurig has a charcoal water filter inside the reservoir, take it out before descaling. Vinegar will damage it.

Tips

  • Use filtered water for daily brewing. This reduces mineral buildup, so you don’t need to descale as often.
  • Descale on a day you have time. The whole process takes about 45 minutes, mostly waiting. Plan to do it when you’re home.
  • Wipe the exterior. Use a damp cloth to wipe the outside and the drip tray area. Vinegar can leave a residue.
  • If your machine has a “Descale” light, it will turn off after the vinegar cycle. If it stays on, you may need to run the cycle again.
  • Store the machine with the reservoir empty. After descaling, let the reservoir dry completely before putting it back.

Troubleshooting

  • Vinegar taste remains after rinsing. Run 2–3 more water-only cycles. If the taste persists, the reservoir may not be rinsed well. Wash it again with soap and water, and rinse thoroughly.
  • Machine won’t brew during descaling. Check that the reservoir is seated properly and has enough liquid. If the machine still won’t brew, unplug it for 5 minutes, then try again.
  • Water leaks from the machine. Make sure the reservoir is fully seated and the lid is closed. If leaking continues, the reservoir O-ring may be dirty—wipe it clean.
  • Descale light stays on. Some models require you to run a full descale cycle, then press and hold the descale button for a few seconds to reset. Check your manual.
  • Slow brewing after descaling. If brewing is still slow, the needle that punctures the K-cup may be clogged. Use a paperclip to gently unclog it (unplug first).

Frequently Asked Questions

How often should I descale my Keurig?

Every 3–6 months, depending on your water hardness. If you notice slower brewing or a change in taste, it’s time to descale.

Can I use apple cider vinegar instead of white vinegar?

White vinegar is recommended because it’s clear and doesn’t leave residue. Apple cider vinegar can leave a smell and may not be as effective.

Do I need to remove the water filter before descaling?

Yes, if your Keurig has a charcoal filter inside the reservoir, remove it before descaling. Vinegar can damage the filter.

Can I use a commercial descaler instead of vinegar?

Yes, Keurig sells a descaling solution that works well. Follow the instructions on the package. Vinegar is cheaper but works just as well.

Will vinegar damage my Keurig?

No, as long as you rinse thoroughly afterward. Vinegar is safe for the internal parts, but leaving it in for too long or not rinsing can leave a taste.

Why is my Keurig making a loud noise during descaling?

This is normal. The vinegar may cause air bubbles in the lines. The noise should stop after the rinse cycles.

Sources: Keurig Support. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.