AjapaReporter

Home life · Updated

How to Descale a Rinnai Tankless Water Heater

Time it takes1 hr 30 min
Steps8in the list below
LevelMediumsome care needed
Official sourceRinnaicheck it for changes

Quick answer To descale a Rinnai tankless water heater, isolate power and gas, connect a pump and hoses to the service valves, then circulate approved flushing solution through the heat exchanger. Follow your model’s manual, and never run the heater during flushing.

Descaling dissolves mineral deposits that can restrict water flow and reduce heating performance. The procedure below covers common Rinnai residential models with service valves; valve arrangements and instructions vary, so check the manual for your exact model before starting. If your unit has no service valves, or you are unsure how to isolate gas or water safely, arrange service with a qualified technician.

What You’ll Need

  • Two descaling or washing-machine hoses that fit the unit’s service valves
  • A submersible circulation pump suitable for the flushing solution
  • A clean bucket large enough to hold the solution and keep the pump submerged
  • Descaling solution approved for your model, or food-grade white vinegar if the manual permits it
  • Gloves and eye protection
  • The Rinnai installation or owner’s manual for your model

Do not use hydrochloric/muriatic acid, bleach, or an unapproved chemical. Check the manual for the correct solution, quantity, and flush duration. If using vinegar, use undiluted food-grade white vinegar only if permitted; do not mix it with other cleaners.

Step-by-Step

  1. Check the model instructions. Find the model number on the heater’s rating plate and confirm the manual’s descaling instructions, including permitted solution, valve positions, and flushing time. Make sure the unit has service valves and that you can reach them safely.
  2. Shut the heater down. Turn off the unit using its controller, then disconnect electrical power at the switch or breaker. Close the manual gas shutoff valve to the heater. Let the unit cool; do not begin while hot. Keep the work area dry and do not touch electrical parts with wet hands.
  3. Isolate the water supply. Close the cold-water inlet service valve and the hot-water outlet service valve. Close the main water supply if your installation requires it. Open a nearby hot-water tap briefly to relieve pressure, then close it. Follow the manual if the valve layout differs.
  4. Connect the hoses and pump. Remove the caps from the cold and hot service ports. Attach one hose from the pump outlet to the cold-water service port. Attach the other hose from the hot-water service port back into the bucket. Tighten connections securely, but do not force them. Keep the pump unplugged for now.
  5. Prepare the flushing solution. Put the pump in the bucket and add the approved solution in the amount specified by the manufacturer. Keep the pump covered by liquid, and position the bucket so the return hose discharges into it without splashing. Do not fill beyond the bucket’s safe capacity.
  6. Circulate the solution. Open both service valves, leaving the main cold-water supply to the heater closed. Check for leaks before plugging in the pump. Run it for the duration specified in the manual, checking the bucket and connections regularly. Stop immediately if a hose slips, a leak appears, or the pump runs dry.
  7. Rinse the heat exchanger. Unplug the pump, remove it from the bucket, and discard the used solution according to its label and local disposal guidance. To rinse, place the pump in a bucket of clean water and circulate it through the same hose loop. If the manual instead calls for a direct water rinse, follow its sequence. Do not open the main supply while the pump loop is still connected unless the manual directs you to.
  8. Restore the heater and check operation. Close the service valves, disconnect the hoses, and replace the service-port caps. Open the cold-water inlet valve, then the hot-water outlet valve, and check all connections for leaks. Open a hot tap until water flows steadily and air is cleared. Restore electrical power and reopen the gas shutoff only after the unit is reassembled and dry. Follow the manual to restart, then check for error codes and leaks.

Common Mistakes

  • Leaving power or gas on: The heater must not fire during descaling. Shut it down and isolate power and gas before connecting the flushing loop.
  • Using the wrong chemical: Strong acids or mixed household cleaners can damage components and create hazards. Use only a solution permitted by Rinnai for your model.
  • Reversing the hose connections: Connect the pump outlet to the cold service port and the return hose to the hot service port, unless your model’s manual specifies a different setup.
  • Forgetting the rinse: Residual descaler can remain inside the water path. Complete the manufacturer’s rinse procedure before restoring normal service.
  • Opening a service port under pressure: Water can spray when a cap is removed. Isolate the valves and relieve pressure first, then open ports slowly with a bucket and cloth ready.

Tips

  • Photograph the valve positions before changing them, and label hoses if the connections are not obvious.
  • Use a stable bucket and keep the pump’s power connection away from liquid. Use a properly protected electrical outlet and follow the pump’s safety instructions.
  • Keep children and pets away from the work area and from used solution.
  • Record the service date. If scaling returns quickly, ask a qualified technician about water hardness, filtration, or a water-treatment system rather than increasing chemical strength or flush time.

Troubleshooting

  • The pump does not circulate: Unplug it before inspecting. Confirm it is submerged, the hoses are not kinked, and the service valves are open. Check the pump’s own instructions; do not run it dry.
  • A connection leaks: Stop and unplug the pump, then close the service valves. Check that the hose fitting is compatible and seated correctly. Replace a damaged washer or hose; do not compensate by overtightening.
  • The heater will not restart: Verify the service caps are back on, the water valves are open, the gas valve and power are restored, and a hot tap has been opened to clear air. Consult the model manual for any displayed error code. Do not repeatedly reset an unexplained fault.
  • Water flow is still weak or an error returns: Descaling may not address a clogged inlet screen, a plumbing restriction, or another fault. Shut the unit down and contact a qualified technician if the manual’s checks do not resolve it.
  • You cannot identify the valves or isolate the unit: Stop rather than guessing. Have a qualified technician perform the service.

Frequently Asked Questions

How often should I descale a Rinnai tankless water heater?

There is no single interval for every home. Follow the maintenance schedule in your model’s manual; water hardness, usage, and any water-treatment equipment affect how often servicing is needed.

Can I use vinegar to descale it?

Only if your exact model’s instructions allow it. Use food-grade white vinegar as directed, and never combine it with another cleaner. The manual takes precedence over general advice.

Can I descale the heater without service valves?

Do not improvise a hose connection or remove plumbing components to create a flushing loop. If service valves are not installed, ask a qualified technician about the appropriate procedure.

Do I need to turn off gas and electricity?

Yes. Shut the heater down, disconnect electrical power, and close its manual gas shutoff before descaling. Keep them off until the hoses are removed, the unit is reassembled, and the area is dry.

What if the heater still shows an error after descaling?

Check the model manual for the meaning of the code and confirm that water, gas, and power are restored correctly. If the code persists, stop resetting the unit and contact a qualified technician.

Sources: Rinnai. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.