Home life · Updated
How to Fix a Leaking Bathroom Sink Faucet
Quick answer Fixing a leaking bathroom sink faucet usually means replacing a worn washer, O-ring, or cartridge. Turn off the water supply, disassemble the handle, and swap the faulty part—most repairs take under an hour.
Before you start, identify your faucet type: compression (two handles, washer-based), ball or cartridge (single handle), or ceramic disc. The steps below cover the most common compression and cartridge types. You’ll need a few basic tools and a replacement part—take the old one to a hardware store if unsure.
What You’ll Need
- Adjustable wrench or pliers
- Screwdriver (Phillips and flathead)
- Replacement washers, O-rings, or cartridge (match your faucet)
- Plumber’s tape (thread seal tape)
- Bucket or towel to catch water
- Penetrating oil (if parts are stuck)
- Safety glasses (optional)
Step-by-Step
- Turn off the water supply. Locate the shut-off valves under the sink (usually two: hot and cold). Turn them clockwise until they stop. Open the faucet to release any remaining water pressure, then close it.
- Plug the drain. Place the sink stopper or a rag over the drain to prevent small parts from falling in.
- Remove the handle. Pry off the decorative cap (often marked H or C) with a flathead screwdriver. Unscrew the handle screw underneath, then lift the handle off. If it’s stuck, spray penetrating oil and wait a few minutes.
- Unscrew the packing nut. Use an adjustable wrench to loosen the large nut that holds the valve stem in place. Turn counterclockwise. Be careful not to strip it—apply steady pressure.
- Pull out the valve stem. Grip the stem and pull it straight out. For cartridge faucets, you may need to pull the cartridge out with pliers (grip the top, not the sides).
- Inspect and replace the washer or O-ring. Look at the rubber washer at the bottom of the stem—if it’s worn, cracked, or flattened, replace it. Also check the O-ring around the stem. Remove the old ones with a screwdriver or your fingers.
- Install the new parts. Press the new washer into the slot (make sure it sits flat). Slide the new O-ring into its groove. Apply a thin layer of plumber’s grease if you have it—it helps the parts slide and seal.
- Reassemble the faucet. Push the stem back into the faucet body. Tighten the packing nut by hand first, then use the wrench to snug it—don’t overtighten (turn an extra quarter-turn after hand-tight).
- Reattach the handle. Place the handle back on the stem, insert the screw, and tighten. Snap the decorative cap back on.
- Turn the water back on and test. Open the shut-off valves slowly (counterclockwise). Turn the faucet on and off a few times. Check for leaks around the handle and the spout. If it drips, tighten the packing nut slightly more.
Common Mistakes
- Overtightening the packing nut. This can crack the faucet body or strip threads. Hand-tighten, then only a small turn with the wrench.
- Forgetting to turn off the water. You’ll get sprayed and may flood the cabinet. Always shut off the valves first.
- Using the wrong replacement part. Washers and cartridges vary by brand and model. Take the old part to the store to match it.
- Not cleaning the seat. If the valve seat (where the washer presses) is rough or pitted, the new washer will leak. Use a seat dresser or replace the seat if needed.
- Losing small screws. Keep parts in a tray or magnetic dish. They’re easy to drop down the drain.
Tips
- Take a photo of the disassembled faucet before removing parts—it helps when reassembling.
- Use plumber’s tape on threaded connections if you disassemble them, but not on washers or O-rings.
- If your faucet is a single-handle cartridge type, you may need to remove a retaining clip or pin before pulling the cartridge—check for a small metal clip near the base.
- For ceramic disc faucets, leaks often come from a worn cartridge—replace it entirely, as internal parts aren’t serviceable.
- If the handle is hard to turn after reassembly, loosen the packing nut a quarter-turn—it may be too tight.
Troubleshooting
- Faucet still leaks after replacing the washer. The valve seat may be worn or pitted. Use a seat dressing tool to smooth it, or replace the seat (it unscrews with a seat wrench).
- Water leaks from under the handle. The O-ring or packing nut is likely faulty. Replace the O-ring and ensure the nut is snug but not overtightened.
- Water sprays from the spout base. The spout’s O-rings (on some models) are worn. You’ll need to remove the spout and replace those rings.
- Can’t get the handle off. Use a handle puller tool (available at hardware stores) or gently tap the handle with a rubber mallet to break the corrosion seal.
- No water comes out after reassembly. You may have left the shut-off valves closed, or the handle is not aligned with the stem. Recheck the handle position and turn the valves fully open.
- Leak persists and you’ve tried everything. The faucet body may be cracked or corroded. In that case, replacing the entire faucet is the practical fix.
Frequently Asked Questions
Why does my faucet drip even when it’s turned off?
Usually a worn washer or cartridge that no longer seals against the valve seat. Replacing it should stop the drip.
Can I fix a leak without turning off the water?
No. You must shut off the water supply to avoid flooding and injury. If you can’t find the shut-off valves, turn off the main water valve for the house.
How do I know if I need a washer or a cartridge?
Two-handle faucets typically use washers; single-handle faucets use cartridges. If you’re unsure, take the part out and bring it to a hardware store for identification.
What if the faucet still leaks after replacing the cartridge?
Check the valve seat for damage, or ensure the cartridge is fully seated and the retaining clip is in place. If the leak continues, the faucet may need replacement.
Is it worth repairing an old faucet or should I replace it?
If the faucet is structurally sound and parts are available, repair is usually cheaper. If it’s badly corroded or cracked, replacement is more reliable.
How often should I replace faucet washers?
There’s no set schedule—replace them when they start to leak. Regular maintenance (once a year) can catch wear early.
Related
- How to Phone NAB: Call the Bank Fast
- How to Shrink Font on Screen: 4 Easy Ways
- How to Print Your Own Stickers at Home
Sources: EPA WaterSense. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.