Home life · Updated
How to Fix a Leaking Faucet Handle
Quick answer A leaking faucet handle is usually caused by a worn O-ring or packing nut. Tightening the nut or replacing the O-ring stops the leak in about 20 minutes with basic tools.
What You’ll Need
- Adjustable wrench or pliers
- Flathead and Phillips screwdrivers
- Replacement O-rings or packing washers (match your faucet brand)
- Plumber’s grease (silicone-based)
- Clean rag or towel
- Penetrating oil (if the handle is stuck)
Step-by-Step
- Turn off the water supply. Locate the shut-off valves under the sink and turn them clockwise until fully closed. Open the faucet to release any remaining water pressure.
- Remove the handle. Pry off the decorative cap (often marked with H or C) using a flathead screwdriver. Unscrew the Phillips screw underneath, then pull the handle straight up. If it’s stuck, spray penetrating oil around the base and wait 5 minutes.
- Inspect the packing nut and O-ring. You’ll see a hex-shaped nut just below the handle. Check if it’s loose—tighten it gently with an adjustable wrench. If the leak persists, the O-ring beneath it is likely worn.
- Replace the O-ring. Unscrew the packing nut completely, then pull out the valve stem. Slide off the old O-ring and replace it with a new one of the same size. Apply a thin coat of plumber’s grease to the new O-ring to help it seat properly.
- Reassemble the faucet. Slide the valve stem back into place, hand-tighten the packing nut, then use the wrench to snug it (avoid overtightening). Reattach the handle and screw the cap back on.
- Turn the water back on and test. Slowly open the shut-off valves, then turn the faucet on and off a few times. Check for drips around the handle. If it still leaks, repeat steps 3–4 and ensure the O-ring is fully seated.
Common Mistakes
- Overtightening the packing nut—this can crack the valve body or strip threads.
- Using the wrong size O-ring—an ill-fitting ring will leak just as much.
- Forgetting to turn off the water—you’ll get sprayed and risk flooding.
- Not greasing the new O-ring—dry rubber can tear during installation.
Tips
- Take the old O-ring to the hardware store to match it exactly.
- Use silicone plumber’s grease, not petroleum jelly, which can degrade rubber.
- Clean any mineral deposits from the valve stem with vinegar before reassembling.
- If the handle is corroded, replace it while you have it off—it’s cheap and easy.
Troubleshooting
If the leak continues after replacing the O-ring, the valve seat itself may be worn or corroded. Use a valve seat wrench to remove and replace it, or install a valve seat dressing tool to smooth it. If water seeps from the top of the handle when the faucet is on, the packing nut is likely loose—tighten it slightly. If the handle itself is cracked, water can travel through it; replace the handle. When the shut-off valves won’t close fully, you may need to replace them or use a main water shut-off for the whole house.
Frequently Asked Questions
Why does my faucet leak only when the handle is turned on?
This usually means the O-ring around the valve stem is worn. When the handle is off, the O-ring isn’t under pressure; when you turn it on, water escapes past the damaged ring.
Can I fix a leaking handle without turning off the water?
No. You must shut off the water supply to avoid a flood and to work safely. If you don’t have shut-off valves under the sink, turn off the main water valve for your home.
What if the handle is stuck and won’t come off?
Spray penetrating oil around the base of the handle and wait 10–15 minutes. Then gently tap the handle upward with a rubber mallet. If it still won’t budge, use a handle puller tool (available at hardware stores).
How do I know which O-ring size to buy?
Remove the old O-ring and take it to a hardware store. They can match it by size. Alternatively, check your faucet’s brand and model number online or in the manual.
Is it worth calling a plumber instead?
For a simple O-ring replacement, most DIYers can do it in 20 minutes. But if you have a cartridge or ceramic disc faucet (common in newer models), the repair is more complex—call a plumber if you’re unsure.
Why does my faucet leak at the base of the handle even after tightening?
That leak is often from the packing nut or the O-ring, not the handle itself. If tightening doesn’t fix it, the O-ring is likely worn or the valve stem is corroded. Replace the O-ring or the entire stem if needed.
Related
- How to Phone New Zealand from the UK
- How to Shrink Header Size in Word
- How to Phone New York from the UK: Step-by-Step
Sources: EPA WaterSense. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.