AjapaReporter

Home life · Updated

Fix a Leaking Faucet: Step-by-Step Guide

Time it takes30 min
Steps7in the list below
LevelEasyno special skills
Official sourceEPA WaterSensecheck it for changes

Quick answer To fix a leaking faucet, first turn off the water supply, then disassemble the handle and replace the worn washer, O-ring, or cartridge. Reassemble and test—most leaks stop after replacing these small parts.

This guide walks you through fixing a standard compression faucet (the kind with separate hot and cold handles) and also covers cartridge and ball-type faucets. You’ll learn what parts to check, how to replace them, and common mistakes to avoid. Before you start, identify your faucet type—compression, cartridge, ball, or ceramic disk—because the repair differs slightly. Most home improvement stores sell universal repair kits that fit many models.

What You’ll Need

  • Adjustable wrench
  • Screwdriver (flathead and Phillips)
  • Replacement parts: washers, O-rings, cartridge, or ball assembly (match your faucet type)
  • Plumber’s grease (silicone-based)
  • Pipe tape (thread seal tape)
  • Bucket or towel to catch water
  • Penetrating oil (if parts are stuck)

Step-by-Step

  1. Turn off the water supply. Look under the sink for the shut-off valves (usually two small knobs). Turn them clockwise to close. If there are no shut-off valves, turn off the main water valve for your home. Open the faucet to release any remaining water pressure.
  2. Plug the drain and remove the handle. Place a sink plug or a cloth over the drain to prevent losing small parts. Use a screwdriver to remove the screw holding the handle (often under a decorative cap). Pull the handle off; if it’s stuck, use a wrench gently or apply penetrating oil.
  3. Remove the bonnet or packing nut. Under the handle, you’ll see a large nut (bonnet) that holds the stem. Use an adjustable wrench to unscrew it counterclockwise. For cartridge faucets, you may need to pull out a retaining clip first.
  4. Inspect and remove the stem or cartridge. For compression faucets, the stem will come out with the nut. For cartridge faucets, pull the cartridge straight out. For ball-type faucets, you’ll see a ball and cam assembly. Examine the parts for wear, cracks, or mineral buildup.
  5. Replace the washer or O-ring. At the bottom of the stem, you’ll find a rubber washer (for compression) or O-rings around the stem. Remove the old ones and replace with new ones of the same size. Apply a thin layer of plumber’s grease to the new rubber parts to help them seal and slide.
  6. Reassemble the faucet. Insert the new stem or cartridge back into the faucet body. Tighten the bonnet nut with your wrench, but don’t overtighten—snug is enough. Reattach the handle and screw it in place. Turn the water supply back on slowly and check for leaks.
  7. Test and fine-tune. Turn the faucet on and off a few times. If it still leaks, the issue may be the valve seat (the part the washer presses against). You can use a seat wrench to remove and replace it, or use a seat grinder to smooth it. If the leak is around the handle, tighten the packing nut slightly.

Common Mistakes

  • Not turning off the water—always shut off the supply first to avoid flooding.
  • Overtightening nuts—this can crack the faucet body or strip threads.
  • Using the wrong replacement parts—bring the old parts to the store to match sizes.
  • Skipping the plumber’s grease—dry rubber parts can bind and wear quickly.
  • Forgetting to clean the valve seat—if the seat is rough, a new washer won’t seal.

Tips

  • Take a photo of the disassembled parts before removal to help with reassembly.
  • Use a basin wrench for hard-to-reach nuts under the sink.
  • If your faucet is a single-handle type, it likely uses a cartridge—replace it entirely.
  • Apply pipe tape to the threads of the bonnet nut if it leaks around the handle.
  • Turn off the water at the main if you have no shut-off valves—do this before starting.

Troubleshooting

Faucet still leaks after replacing the washer. The valve seat may be worn or corroded. Use a seat wrench to remove it and replace it, or use a seat grinder to smooth it. Also check that the washer is the correct size and properly seated.

Water leaks from under the handle. This usually means the packing nut or O-ring around the stem is worn. Tighten the packing nut slightly, or replace the O-ring and apply grease.

Handle is hard to turn. The stem or cartridge may be corroded. Remove it and clean with vinegar, then lubricate with plumber’s grease. If it’s still stiff, replace the cartridge.

Parts are stuck. Apply penetrating oil and wait 15 minutes before trying again. Use a wrench with a cloth to avoid scratching. If the screw is stripped, use a screw extractor.

You can’t find the shut-off valves. Check under the sink again—they may be behind insulation. If not, turn off the main valve near the water meter. If you live in an apartment, contact the building manager.

Frequently Asked Questions

Why does my faucet leak only when it’s turned on?

This usually means the washer or O-ring is worn, and water escapes around the stem when pressure is applied. Replacing the washer or cartridge typically fixes it.

How do I know if my faucet uses a washer or a cartridge?

If it has two handles, it’s likely a compression faucet with a washer. If it has one handle, it’s probably a cartridge or ball type. Remove the handle and look—if you see a metal stem with a rubber washer at the bottom, it’s compression; if you see a plastic or brass cylinder, it’s a cartridge.

Can I fix a leaking faucet without turning off the water?

No, you must turn off the water supply. Otherwise, water will spray out and you risk flooding your kitchen or bathroom.

What if my faucet is still leaking after replacing all parts?

The valve seat may be damaged. Replace it with a new one, or consider replacing the entire faucet if it’s old and corroded.

Is it worth fixing an old faucet or should I replace it?

If the faucet body is in good condition, replacing the internal parts is cheaper and easy. But if the finish is worn or it’s constantly leaking, a new faucet may be more cost-effective in the long run.

How often should I replace faucet washers?

There’s no set schedule—washers wear out over time depending on usage. If you notice a drip, it’s time to replace them. Regular maintenance can extend their life.

Sources: EPA WaterSense. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.