Home life · Updated
Fix a Leaking Tap: Step-by-Step Guide
Quick answer Turn off the water supply, disassemble the tap, replace the worn washer or O-ring, and reassemble. Most leaks stop once the faulty seal is swapped.
What You’ll Need
- Adjustable wrench or spanner
- Flathead and Phillips screwdrivers
- Replacement washers or O-rings (match size and type)
- Plumber’s tape (thread seal tape)
- Clean cloth or rag
- Bucket or container to catch water
- Penetrating oil (if parts are stuck)
Step-by-Step
- Turn off the water supply. Locate the isolation valve under the sink or the main shut-off valve for your home. Turn it clockwise until it stops. Open the tap to release any remaining water and confirm the flow has stopped.
- Plug the drain and protect the surface. Put the plug in the sink to catch small parts. Lay a cloth over the drain to avoid losing screws or washers.
- Remove the tap handle. Look for a small screw on the top or side of the handle. It may be hidden under a decorative cap (prise it off with a flathead screwdriver). Unscrew and lift the handle off. If it’s stuck, gently wiggle it while pulling upward.
- Unscrew the bonnet or packing nut. Use the adjustable wrench to loosen the large nut beneath the handle. Turn counterclockwise. If it’s tight, apply penetrating oil and wait a few minutes before trying again.
- Lift out the valve or cartridge. For a traditional tap, you’ll see a stem with a rubber washer at the bottom. For a cartridge tap, pull out the whole cartridge. Take note of how it sits so you can reinstall it correctly.
- Replace the washer or O-ring. Remove the old washer from the stem or the O-rings from the cartridge. Take the old part to a hardware store to match the size and type. Fit the new one securely in place.
- Reassemble the tap. Insert the valve or cartridge back into the tap body. Tighten the bonnet nut with the wrench, but do not overtighten—snug is enough. Replace the handle and screw it in place.
- Turn the water back on and test. Slowly open the shut-off valve. Turn the tap on and off a few times to check for leaks. If it still drips, you may need to replace the O-ring on the spout or the entire cartridge.
Common Mistakes
- Not turning off the water supply properly, leading to a flood when you loosen the nut.
- Using the wrong size washer—too small won’t seal, too large won’t fit.
- Overtightening the bonnet nut, which can crack the tap body or strip threads.
- Forgetting to clean the valve seat (the part the washer presses against) before replacing the washer.
- Losing small screws or caps because the drain wasn’t plugged.
Tips
- Take the old washer or cartridge with you when buying a replacement—it ensures you get the exact match.
- Apply plumber’s tape to the threads of the bonnet nut if they look worn, to prevent leaks from the joint.
- If the tap is a ball or ceramic disc type, the fix may involve replacing the whole cartridge rather than just a washer.
- Clean mineral deposits from the valve seat with a cloth or fine abrasive pad before reassembling.
- Keep a small tray or magnetic dish to hold screws and parts while you work.
Troubleshooting
- Water still leaks from the spout after replacing the washer: The valve seat may be worn or pitted. Use a seat dressing tool to smooth it, or replace the entire valve.
- Leak around the base of the tap handle: This usually means the O-ring around the stem is worn. Replace it with a new one of the same size.
- Tap is hard to turn after reassembly: The bonnet nut may be too tight. Loosen it slightly until the handle moves smoothly.
- Water leaks from the spout even when the tap is closed: The washer may not be seating properly. Check that it’s the right size and that the valve stem is fully inserted.
- Parts are stuck and won’t budge: Apply penetrating oil and wait 15 minutes. Use a wrench with a cloth to avoid scratching the finish. If still stuck, call a plumber.
Frequently Asked Questions
Why does my tap leak even after replacing the washer?
The valve seat (the metal surface the washer presses against) may be worn or corroded. Smooth it with a seat dressing tool or replace the entire valve.
Do I need to turn off the water to the whole house?
No, most taps have an isolation valve under the sink. Turn that off first. If not, use the main shut-off valve for your home.
How do I know if I need a washer or an O-ring?
If the leak is from the spout, it’s usually the washer. If it’s from around the handle, it’s likely the O-ring. Some taps use cartridges that contain both.
Can I fix a dripping tap with just plumber’s tape?
Plumber’s tape helps seal threaded joints but won’t fix a worn washer. The tape is a temporary measure at best; replace the washer for a lasting fix.
What if my tap is a modern mixer type?
Mixer taps often use ceramic cartridges. You’ll need to remove the handle and unscrew the cartridge, then replace it with an identical one.
Is it worth calling a plumber instead?
If you’re uncomfortable with the disassembly or the tap is complex, a plumber can fix it quickly. But for most standard taps, the DIY repair is straightforward.
Related
- How to Shrink Jeans That Are Too Big
- How to Write a Novel for Beginners
- How to Shrink Rubber: 5 Methods That Work
Sources: UK Government - Water Regulations. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.