Home life · Updated
How to Stretch Audio in FL Studio: 2 Easy Ways
Quick answer In FL Studio, you stretch audio by opening the sample in the Channel Rack, enabling the Stretch knob, and setting the Mode to “Stretch” or “Tonal.” This changes the length and tempo of the clip without changing its pitch.
What You’ll Need
- FL Studio (any recent version; menus may differ slightly by version)
- An audio clip or sample loaded into the Channel Rack or Playlist
- Basic familiarity with the Channel Rack and Playlist panels
Step-by-Step
- Load your audio clip. Drag and drop an audio file (WAV, MP3, OGG, etc.) from your browser into the Channel Rack or directly onto the Playlist. If you drop it on the Playlist, it becomes an audio clip; if you drop it on the Channel Rack, it becomes a sampler channel.
- Open the Channel Settings. Double-click the sample’s name in the Channel Rack (or the audio clip in the Playlist). This opens the Channel Settings window. For an audio clip in the Playlist, double-click the clip itself to open the Audio Clip properties.
- Find the Time Stretch section. In the Channel Settings, look for the “Time” panel (usually in the middle of the window). It contains a knob labeled “Stretch” and a dropdown menu labeled “Mode.” For audio clips in the Playlist, the same controls appear in the Audio Clip window under the “Time” tab.
- Set the Mode to Stretch or Tonal. Click the Mode dropdown and select “Stretch” (best for drums and rhythmic material) or “Tonal” (best for vocals, pads, and melodic parts). The “Stretch” mode preserves transients, while “Tonal” preserves pitch and formants better for sustained sounds.
- Adjust the Stretch knob. Turn the Stretch knob clockwise to lengthen the sample (slower tempo) or counterclockwise to shorten it (faster tempo). The pitch stays the same because the mode is set to Stretch or Tonal. The percentage shown next to the knob indicates the new length relative to the original (100% = original).
- Use the Playlist for precise timing. If you want the stretched audio to fit a specific number of bars, place the audio clip in the Playlist, then use the “Fit to Tempo” feature. Right-click the clip, choose “Fit to Tempo,” and select the number of bars you want it to span. FL Studio automatically calculates the correct stretch amount.
- Render or export the result. Once you are happy with the stretch, you can keep it as a live effect or render it to a new audio file. To render, select the clip in the Playlist, go to the top menu “Tools” > “Consolidate Clip from Selection” (or press Alt+C). This bakes the stretch into a new audio file.
Common Mistakes
- Leaving Mode on “Resample.” The default mode is “Resample,” which changes pitch when you stretch. If you do not switch to Stretch or Tonal, your audio will sound like a chipmunk or a slowed-down monster.
- Stretching too far. Stretching beyond 150% or below 50% often introduces artifacts like warbling or metallic sounds. If you need extreme changes, consider re-recording or using a different sample.
- Forgetting to enable “Stretch” for Playlist clips. In the Playlist, the audio clip has its own stretch settings. If you only adjust the Channel Rack, the Playlist clip may not update. Always check the clip’s own properties.
- Confusing length with tempo. The Stretch knob changes length, but if your project tempo changes, the clip may not follow. Use the “Fit to Tempo” option to match the project BPM automatically.
Tips
- Use “Stretch” mode for drums and percussive loops to keep the attack punchy. Use “Tonal” mode for vocals and instruments to avoid unnatural formant shifts.
- If you want to stretch a sample without changing its pitch but also want to keep the original pitch-shifting ability, try the “e3 Generic” or “e3 Tonal” modes in the Mode dropdown. These are more advanced but offer higher quality for extreme stretches.
- Right-click the Stretch knob to reset it to 100% instantly. This is handy when you experiment and want to start over.
- For multi-bar loops, use “Fit to Tempo” and select the correct number of bars. This is much faster than manually adjusting the knob.
- If you are stretching a sample that has a lot of reverb or delay, be aware that those effects will also be stretched. Consider applying effects after stretching.
Troubleshooting
- Pitch changes when I stretch. You are likely in “Resample” mode. Open the Channel Settings or Audio Clip properties and change the Mode to “Stretch” or “Tonal.”
- Stretch knob is grayed out. This happens when the audio clip is not selected or the window is not focused. Make sure you have double-clicked the correct clip and that the Time panel is visible. If it still won’t work, try closing and reopening the window.
- Audio sounds warbly or distorted. The stretch amount is too extreme for the selected mode. Try a different mode (e.g., switch from Stretch to Tonal) or reduce the stretch percentage. Also check that the sample’s root key is set correctly in the Channel Settings (the “Root note” field) if you are using Tonal mode.
- The clip does not match the project tempo. Use “Fit to Tempo” in the Playlist. Right-click the clip, select “Fit to Tempo,” and choose the number of bars. If the clip still drifts, make sure the project tempo is set correctly and that the clip’s “Time” setting is not set to “None.”
- Stretched audio is not playing in sync. Check the “Start offset” in the Channel Settings. If the original sample had silence at the beginning, the stretch may shift the timing. Trim the silence first or use the “Start” knob to adjust.
Frequently Asked Questions
Does stretching audio in FL Studio affect the pitch?
No, when you use the Stretch or Tonal mode, the pitch remains unchanged. Only the length and tempo change. The Resample mode, however, will change pitch along with length.
What is the difference between “Stretch” and “Tonal” modes?
Stretch mode is designed for rhythmic material like drums and percussion, preserving the attack transients. Tonal mode is better for melodic content like vocals and instruments, preserving the harmonic structure and formants more accurately.
Can I stretch an audio clip in the Playlist without affecting the original file?
Yes, stretching is non-destructive. The original file on your hard drive remains unchanged. The stretch is applied as a live effect in FL Studio, and you can render it to a new file if you want to save it.
How do I stretch audio to a specific number of bars?
Place the clip in the Playlist, right-click it, choose “Fit to Tempo,” and select the number of bars you want. FL Studio will automatically calculate the correct stretch percentage based on your project tempo.
Why does my stretched audio sound like a robot?
This usually happens when the stretch amount is too large or the mode is not suited to the material. Try using Tonal mode for vocals or switch to a higher-quality algorithm like “e3 Tonal” if available. Also, check that the sample’s root note is set correctly.
Can I stretch multiple audio clips at once?
Yes, you can select multiple clips in the Playlist (hold Ctrl and click each clip), then right-click and choose “Fit to Tempo” or adjust the stretch settings in the Channel Rack if they share the same channel. However, each clip’s settings are independent, so you may need to adjust them individually for precise results.
Related
- How to Shrink Video Size: Easy Ways for Any Device
- How to Turn Off an Android Tablet
- How to Shrink to Fit in Word
Sources: Image-Line FL Studio Help. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.