AjapaReporter

Home life · Updated

How to Stretch Multiple Lines in AutoCAD

Time it takes5 min
Steps6in the list below
LevelEasyno special skills
Official sourceAutodesk Supportcheck it for changes

Quick answer To stretch multiple lines in AutoCAD, use the STRETCH command (or its alias S), select the lines with a crossing window or polygon, and then drag or enter a displacement to extend or shorten them simultaneously.

What You’ll Need

  • AutoCAD (any recent version, including AutoCAD LT)
  • A drawing with lines or other objects you want to stretch
  • Basic familiarity with selecting objects and using commands

Step-by-Step

  1. Start the STRETCH command. Type STRETCH (or S) in the command line and press Enter. You can also find it on the Home tab under Modify, or right-click and choose Stretch from the context menu.
  2. Select objects with a crossing window. When prompted to “Select objects,” click a point to the right of the lines you want to stretch, then drag left to create a green (or dashed) crossing window. Only objects that are partially inside this window will be stretched; objects fully inside will be moved.
  3. Include all lines you need. Click each line you want to include if the crossing window missed any. Hold Shift and click to remove objects from the selection set. Press Enter when done.
  4. Specify a base point. After selection, AutoCAD prompts “Specify base point.” Click a point that will act as the anchor for the stretch. This is typically a corner or endpoint of the selected geometry.
  5. Specify the second point or displacement. Click a second point to define how far and in what direction to stretch. Alternatively, type a relative coordinate like @5,0 to stretch 5 units to the right, or type an absolute distance and direction (e.g., 0,10 for 10 units up).
  6. Press Enter to finish. The selected lines will stretch (or shorten) according to your input. If you need to undo, press Ctrl+Z immediately.

Common Mistakes

  • Using a window instead of a crossing window. A regular window (blue, dragged left-to-right) selects only objects fully inside, so lines that cross the boundary won’t be stretched—they’ll just move or be ignored.
  • Selecting objects with a pick box. Clicking directly on a line selects it entirely, so it will move rather than stretch. You must use a crossing selection for the stretch effect.
  • Forgetting to include endpoints. If a line’s endpoint is outside the crossing window, that end won’t move. Make sure the crossing window covers the parts you want to stretch.
  • Not using relative coordinates. When typing a displacement, entering 5,0 moves the selection 5 units in X and 0 in Y from the current origin, not from the base point. Use @5,0 to specify a relative distance from the base point.
  • Stretching with Ortho off. If you need a perfectly horizontal or vertical stretch, turn on Ortho (F8) to constrain the direction.

Tips

  • Use a crossing polygon for complex selections. Type CP (crossing polygon) after starting STRETCH to draw an irregular shape that selects objects crossing its boundary.
  • Stretch multiple objects with grips. Select the lines first, then click a grip (the blue squares at endpoints) and drag. This works for multiple lines if you select them all and then click one grip.
  • Use the Stretch tool in the Ribbon. On the Home tab, the Modify panel has a Stretch icon. It works the same as the command.
  • Combine with Object Snaps. While specifying the second point, use object snaps (like Endpoint or Intersection) to stretch precisely to another object.
  • Practice with a simple rectangle. Draw a rectangle and stretch one corner to see how the two adjacent lines stretch and the opposite corner stays fixed.

Troubleshooting

  • Lines move instead of stretching. This happens when you select objects with a window (not crossing) or pick them individually. Undo and redo the selection using a crossing window that only partially covers the lines.
  • Only some lines stretch. Check that the crossing window actually covers the endpoints you want to move. If a line is fully inside, it will move; if it’s fully outside, it won’t change. Adjust the window to include the parts you want to affect.
  • Stretch goes the wrong direction. Verify the base point and second point. If you type coordinates without @, you’re using absolute coordinates. Use @ for relative displacement from the base point.
  • Command not working. Make sure you’re not in a viewport or paper space where the command is disabled. Also check if the layer is locked—if so, objects on that layer won’t stretch. Unlock the layer first.
  • Stretch doesn’t affect dimensions. If you have associative dimensions, they may update automatically. If not, use the DIMREGEN command to refresh them.

Frequently Asked Questions

What is the difference between STRETCH and EXTEND?

STRETCH moves selected objects while keeping connections to other objects, changing their length and shape. EXTEND lengthens objects to meet a boundary edge, but doesn’t move the whole object.

Can I stretch multiple lines at once without selecting each one?

Yes, use a crossing window or crossing polygon to select multiple lines in one go. The STRETCH command applies the same displacement to all selected objects that are partially inside the selection.

Why does my STRETCH command move the whole line instead of stretching it?

That happens when you select the line with a window (blue) or by clicking it directly. For stretching, you must use a crossing window (green, dragged right-to-left) that only partially intersects the line.

How do I stretch lines in a specific direction, like at an angle?

After selecting the lines, specify a base point, then type a relative polar coordinate like @5<45 to stretch 5 units at a 45-degree angle. You can also use object snaps to snap to a point along the desired direction.

Can I stretch lines in AutoCAD LT?

Yes, the STRETCH command is fully available in AutoCAD LT. The steps are identical.

What if I want to stretch lines but keep their lengths the same?

That would be moving, not stretching. Use the MOVE command (or select and drag with grips) to relocate lines without changing their length.

Sources: Autodesk Support. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.