AjapaReporter

Home life · Updated

How to Stretch Woven Wire Fence

Time it takes2 hr
Steps8in the list below
LevelMediumsome care needed
Official sourceUSDA Natural Resources Conservation Servicecheck it for changes

Quick answer Stretching woven wire fence keeps it taut, prevents sagging, and ensures livestock stay contained. You'll need a fence stretcher, come-along or tractor, and a few basic tools.

What You’ll Need

  • Woven wire fence roll
  • Fence stretcher (come-along or tractor-mounted)
  • Fence posts (line and corner posts)
  • Post hole digger or driver
  • Wire ties or staples
  • Fence pliers
  • Gloves and safety glasses

Step-by-Step

  1. Set corner posts – Install sturdy corner posts (e.g., 6-8 inch diameter) at each end of the fence line, set deep in concrete or firmly tamped. These will bear the stretching tension.
  2. Install line posts – Place line posts every 10-15 feet between corners. Use a string line to keep them straight. Height should match the fence roll width.
  3. Unroll the wire – Lay the woven wire roll along the ground next to the posts, with the bottom edge facing the ground. Unroll it fully, allowing some extra length at each end.
  4. Attach to one end post – Secure the wire to a corner post using wire ties or staples. Start at the top and work down, pulling the wire snug by hand initially.
  5. Attach the stretcher – Hook the fence stretcher to the free end of the wire. If using a come-along, attach it to a sturdy anchor (like a tree or vehicle). For a tractor-mounted stretcher, follow the manufacturer’s instructions.
  6. Stretch the wire – Slowly tighten the stretcher until the wire is taut. Aim for a tension where the wire has no sag but isn’t over-stretched (which can deform the mesh). Check for even tension along the entire length.
  7. Secure to the other end – While maintaining tension, fasten the wire to the opposite corner post with ties or staples. Work from top to bottom, pulling each strand tight.
  8. Attach to line posts – Staple the wire to each line post, starting from one end and working to the other. Use fencing staples, driving them at a slight angle to avoid splitting the wood. Ensure the wire is snug against each post.

Common Mistakes

  • Over-stretching – Pulling too hard can distort the mesh or break wires. Stop when the wire is taut but not drum-tight.
  • Uneven tension – If the wire is tighter at one end, it can cause sagging elsewhere. Stretch gradually and check along the line.
  • Insufficient corner support – Weak corner posts will pull inward under tension. Always use heavy-duty posts and set them securely.
  • Staples driven too deep – Driving staples flush can crush the wire and weaken it. Leave a small gap.

Tips

  • Use a come-along for small stretches; for long runs, a tractor-mounted stretcher saves time.
  • Wear gloves to protect your hands from sharp wire ends.
  • If the wire has a selvage (edge wire), make sure it’s on top and bottom for strength.
  • Leave a few extra inches at each end to wrap around the post for a secure hold.
  • For uneven ground, consider a step-down or step-up in the fence line to maintain tension.

Troubleshooting

  • Wire sags after stretching – Re-tension by reattaching the stretcher and pulling a bit more. If it sags due to post movement, reset the posts.
  • Wire breaks during stretching – Stop immediately. Splice the break with a wire splice or overlap and tie. Reduce tension before continuing.
  • Posts lean – This indicates insufficient bracing. Add diagonal braces to corner posts or reset them deeper.
  • Wire doesn’t lie flat – Check for kinks or twists in the roll. Unroll carefully and straighten any bends.

Frequently Asked Questions

How tight should woven wire fence be?

The wire should be taut enough that it doesn’t sag, but not so tight that it hums when plucked. A good rule is to be able to push it slightly with your hand.

Can I stretch woven wire by hand?

No, woven wire is too heavy and long to stretch by hand. You need a mechanical stretcher like a come-along or a tractor-mounted unit.

How long does it take to stretch a fence?

For a typical 100-200 foot run, expect 2-4 hours including post installation. Longer runs take more time.

What is the best way to attach woven wire to wooden posts?

Use galvanized fencing staples. Drive them at a slight downward angle to avoid splitting the wood, and leave a small gap to avoid crushing the wire.

Do I need to stretch woven wire on both ends?

You stretch from one end, but you need to secure both ends to corner posts. The stretching process pulls the entire line taut.

What if my fence is on a slope?

On slopes, you may need to step the fence down or up. Stretch in sections, and ensure each section is taut before moving to the next.

Sources: USDA Natural Resources Conservation Service. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.