Home life · Updated
How to Descale Keurig Single Cup Coffee Maker
Quick answer Descaling removes mineral buildup from your Keurig’s internal water lines, improving brew temperature and taste. Run a descaling solution through the machine, then rinse thoroughly with fresh water.
Before you start, unplug the Keurig and remove any pod from the K-Cup holder. If your model has a water filter, take it out and set it aside—do not run it through the descaling cycle. Check your owner’s manual for the recommended descaling solution; most Keurig models work with a commercial liquid descaler or a homemade mix of equal parts white vinegar and water. The process is the same for all single-cup Keurig machines, but the exact button labels may vary slightly by model.
What You’ll Need
- Keurig descaling solution (or white vinegar and water)
- Fresh water for rinsing
- A large ceramic mug or container (at least 12 oz)
- A sink or large bowl to catch overflow
- Clean, dry cloth for wiping
Step-by-Step
- Prepare the machine: Unplug the Keurig and remove the water reservoir lid, then lift out the reservoir and empty any remaining water. If your model has a removable filter, take it out and keep it aside. Rinse the reservoir with fresh water.
- Fill with descaling solution: Pour the entire bottle of Keurig descaling solution into the empty reservoir. If using vinegar, fill the reservoir with equal parts white vinegar and water (e.g., 10 oz each for a 10 oz reservoir). Replace the reservoir on the machine.
- Place a large mug on the drip tray: Position a large mug or container (at least 12 oz) on the drip tray to catch the liquid. If your mug is too small, use a large bowl or pitcher.
- Run a brew cycle without a pod: Plug the Keurig back in and turn it on. Lift the handle, do not insert a K-Cup, and close it. Place the mug under the spout. Press the largest cup size button (or the “Brew” button) and let the machine run. The descaling solution will flow through the internal lines.
- Repeat until the reservoir is empty: After the first cycle, empty the mug and pour the collected liquid down the sink. Repeat the brew cycle (without a pod) until the reservoir is empty. This may take 5–6 cycles for a full reservoir.
- Let the machine sit: Once the reservoir is empty, leave the machine on and let it sit for 30 minutes. This allows the solution to break down mineral deposits inside the heating element and tubing.
- Rinse with fresh water: Remove the reservoir, rinse it thoroughly with fresh water, and fill it with clean water to the MAX line. Replace it on the machine. Place the mug back under the spout and run 2–3 brew cycles (without a pod) to flush out any remaining solution. Discard the rinse water.
- Clean the exterior and reassemble: Wipe down the exterior with a damp cloth. Reinstall the water filter if you removed it. Run one final brew cycle with fresh water to ensure no aftertaste. Your Keurig is now descaled and ready to use.
Common Mistakes
- Skipping the rinse: Leaving descaling solution in the lines can make your coffee taste bitter or soapy. Always run at least 2–3 fresh-water cycles afterward.
- Using too much vinegar: Vinegar is acidic; using a stronger concentration than 50/50 can leave a lingering odor and may damage seals over time. Stick to equal parts.
- Forgetting to remove the water filter: The filter can absorb the descaling solution and release it later, ruining your coffee. Always remove it before starting.
- Not using a large enough container: If your mug overflows, the solution spills onto the counter and can damage surfaces. Use a container that holds at least the full reservoir volume.
- Running a pod during descaling: Never insert a K-Cup during the descaling process—the solution will ruin the pod and the coffee.
Tips
- Descale regularly: Do this every 3–6 months, or sooner if you notice slower brewing, louder noises, or a change in coffee taste.
- Use the official solution: Keurig’s descaling solution is formulated for your machine and is less likely to leave residue than homemade vinegar.
- Run a water-only cycle first: If you haven’t descaled in a while, run a plain water brew to loosen deposits before adding the solution.
- Keep the reservoir full: After descaling, always keep the reservoir filled with fresh water when not in use to prevent mineral buildup.
- Check your model’s manual: Some models have a “Descale” mode that automates the process—consult your manual for specific instructions.
Troubleshooting
- Machine won’t brew during descaling: Make sure the reservoir is seated properly and the machine is plugged in. If the “Add Water” light stays on, the reservoir may not be making contact—remove and reattach it.
- Vinegar smell remains after rinsing: Run additional fresh-water cycles (up to 5) until the smell fades. You can also fill the reservoir with water and let it sit for an hour before brewing.
- Water flows slowly after descaling: This is normal if mineral deposits were heavy. Run 2–3 more water-only cycles; if it persists, repeat the descaling process.
- Error message appears during descaling: Unplug the machine for 30 seconds, then plug it back in. If the error persists, consult your manual or contact Keurig support.
- Descaling solution didn’t empty fully: If the reservoir still has liquid after several cycles, the machine may have a clog. Run a cycle with the largest cup size and repeat until empty.
Frequently Asked Questions
How often should I descale my Keurig?
Every 3–6 months, depending on water hardness and usage. If you notice slower brewing or off-tasting coffee, descale sooner.
Can I use vinegar instead of the Keurig solution?
Yes, white vinegar is a common alternative. Use equal parts vinegar and water, and rinse thoroughly afterward to avoid lingering taste.
Do I need to remove the water filter before descaling?
Yes, always remove the filter. It can absorb the descaling solution and release it into your coffee later.
Can I descale with a K-Cup in the machine?
No, never insert a K-Cup during descaling. The solution is not meant to be brewed with coffee and will ruin the pod.
Why does my Keurig still taste like vinegar after rinsing?
You may need more rinse cycles. Run 3–5 fresh-water brews, and if the taste persists, let the reservoir sit with fresh water for an hour before brewing again.
What if my Keurig doesn’t have a “Descale” button?
Most models don’t have a dedicated button—just use the largest cup size. Some newer models have a descale mode; check your manual for specifics.
Related
- How to Write a J in Cursive (Step-by-Step)
- How to Shrink a Shirt: 5 Easy Methods
- How to Descale DeLonghi Coffee Machine
Sources: Keurig Support. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.