AjapaReporter

Home life · Updated

How to Fix a Leaking Sink: Step-by-Step Guide

Time it takes30 min
Steps8in the list below
LevelMediumsome care needed
Official sourceEPA WaterSensecheck it for changes

Quick answer Fixing a leaking sink usually involves tightening connections, replacing a worn washer or O-ring, or re-sealing the drain. Turn off the water supply first, then follow the steps below for a dry, leak-free sink.

What You’ll Need

  • Adjustable wrench
  • Plumber’s tape (thread seal tape)
  • Screwdriver (flathead and Phillips)
  • Bucket or towel
  • Replacement washers, O-rings, or faucet cartridge (if needed)
  • Plumber’s putty (for drain leaks)
  • Pipe wrench (for stubborn nuts)
  • Flashlight

Step-by-Step

  1. Turn off the water supply. Locate the shut-off valves under the sink (usually two: hot and cold) and turn them clockwise until they stop. Open the faucet to release remaining water pressure.
  2. Identify the leak source. Dry the area under the sink with a towel, then run water and watch where the drip originates. Common spots: base of the faucet, handles, supply lines, or the drain pipe.
  3. Check and tighten connections. Use an adjustable wrench to gently tighten any loose nuts on the supply lines, the faucet base, or the drain. Avoid over-tightening, which can crack fittings.
  4. Replace the faucet washer or O-ring. If the leak is from the spout or handle, shut off water, remove the handle screw (under a cap), pull off the handle, and inspect the O-ring or washer. Replace any worn parts and reassemble.
  5. Re-seal the faucet base. For leaks around the base, remove the faucet (unscrew mounting nuts under the sink), clean the area, apply a fresh bead of plumber’s putty or silicone sealant, and reinstall.
  6. Fix a leaking drain flange. If water seeps around the drain opening, remove the drain strainer, clean old putty, apply new plumber’s putty, and re-tighten the nut underneath.
  7. Re-tape threaded connections. For leaks at threaded joints (supply lines, drain trap), unscrew, wrap plumber’s tape clockwise around the threads 3–4 times, and reattach.
  8. Test the repair. Turn the water back on, run water for a few minutes, and check all areas for drips. Dry everything thoroughly and re-check after an hour.

Common Mistakes

  • Forgetting to turn off the water supply before starting – always do this first.
  • Over-tightening nuts, which can crack plastic fittings or strip threads.
  • Using plumber’s putty on threaded connections – it’s for sealing flat surfaces, not threads.
  • Not cleaning old putty or tape before applying new – debris causes leaks.
  • Ignoring the source – sometimes the leak is from the supply line, not the faucet, so check all parts.

Tips

  • Use a basin wrench for hard-to-reach nuts under the sink.
  • Take a photo of the plumbing before disassembly to help with reassembly.
  • If you have a sprayer, check its hose connection – a common leak point.
  • For stubborn leaks, replace the entire faucet cartridge rather than just the washer.
  • Always use two wrenches when loosening nuts: one to hold the fitting, one to turn – prevents twisting pipes.

Troubleshooting

  • Leak persists after tightening: The washer or O-ring is likely worn – replace it. If the leak is from a compression fitting, you may need a new ferrule.
  • Water seeps from the base of the faucet: The O-ring under the spout is probably damaged – replace it. If the faucet is old, consider replacing the entire unit.
  • Dripping from the spout when faucet is off: This indicates a worn cartridge or valve seat – replace the cartridge or re-grind the seat with a seat wrench.
  • Leak at the supply line connection: Tighten carefully; if it still leaks, replace the supply line – they can crack internally.
  • Drain leak after re-sealing: Let the putty cure for at least an hour before running water. If it still leaks, remove and reapply with more putty.

Frequently Asked Questions

Why does my sink leak only when I use hot water?

Hot water expands metal parts, which can reveal a loose connection or a worn washer that only leaks under pressure. Check the hot water supply line and the faucet’s hot side cartridge.

Can I use plumber’s putty on all sink parts?

No – plumber’s putty is for flat, non-porous surfaces like the drain flange. Use silicone sealant for areas that may contact water long-term, and thread tape for threaded connections.

How do I know if I need a new faucet instead of a repair?

If your faucet is over 10 years old, has multiple leaks, or parts are no longer available, replacement is often more cost-effective. Also, if the body is corroded, repair won’t last.

Is it safe to use a chemical drain cleaner if my sink leaks?

No – chemical cleaners can damage pipes and worsen leaks. Address the leak first, and avoid harsh chemicals in the future to prevent pipe deterioration.

What if the leak is from the pipe under the sink, not the faucet?

This could be a cracked pipe or a loose joint. Tighten slip nuts on the trap, or replace the affected pipe section. If the pipe is corroded, call a plumber.

How tight should I make the nuts?

Hand-tighten first, then use a wrench to give a quarter-turn. Over-tightening strips threads or cracks fittings. If it still leaks, replace the washer rather than tightening more.

Sources: EPA WaterSense. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.