Home life · Updated
Fix a Leaking Skylight: Step-by-Step Guide
Quick answer Fix a leaking skylight by first identifying the leak source—usually damaged flashing or seals—then cleaning, resealing, or replacing the affected parts. Most leaks can be stopped in under two hours with basic tools.
What You’ll Need
- Ladder (safe, stable, and tall enough to reach the skylight)
- Safety harness or rope (if roof slope is steep)
- Rubber gloves
- Wire brush or stiff nylon brush
- Putty knife or scraper
- Roofing sealant (butyl or polyurethane, exterior grade)
- Roofing cement or flashing tape (if flashing is damaged)
- Replacement flashing or skylight curb (if needed)
- Caulking gun
- Clean rags
- Bucket or container for water testing
- Work gloves and safety glasses
Step-by-Step
- Inspect from inside first. Go into the attic or room directly below the skylight during daylight. Look for water stains, wet insulation, or light coming through gaps. Mark the exact spot with chalk or tape. This tells you where to focus your roof work.
- Clean the area around the skylight. Remove leaves, pine needles, and debris from the roof surface and from the skylight frame. Use a brush to sweep away dirt and old loose sealant. A clean surface is essential for new sealant to bond.
- Check the flashing. Flashing is the metal or rubber material that bridges the skylight and the roof. Look for rust, cracks, lifted edges, or gaps between flashing pieces. If flashing is loose or corroded, it often needs to be replaced. If it’s just lifted, you may be able to re-secure it with roofing cement.
- Remove old sealant. Use a putty knife or scraper to carefully remove old, cracked, or peeling sealant from around the skylight frame and flashing joints. Work gently to avoid damaging the roof shingles or skylight glass.
- Apply new sealant. Load the caulking gun with exterior-grade roofing sealant. Apply a continuous bead along all seams where the skylight meets the roof, and along any flashing joints. Smooth the bead with a wet finger or a putty knife to ensure full contact.
- Replace damaged flashing (if necessary). If flashing is beyond repair, remove the old flashing carefully. Slide new flashing under the shingles above the skylight and over the shingles below it. Secure it with roofing nails and cover nail heads with roofing cement. This step may require removing a few shingles.
- Check the skylight glass seal. Look at the rubber gasket or seal between the glass and the frame. If it’s cracked or compressed, apply a thin bead of clear silicone sealant over the gasket. Do not seal the glass itself permanently—only the gap around it.
- Test with water. After the sealant has cured (check the label, often 24 hours), have a helper spray the skylight with a garden hose from the ground while you watch inside. Start low and work upward. If water appears inside, note the location and reapply sealant to that specific spot.
Common Mistakes
- Sealing the skylight glass itself instead of the seams—this traps moisture and can cause condensation or glass damage.
- Using indoor silicone caulk, which breaks down in UV light.
- Applying sealant over dirty or wet surfaces, causing poor adhesion.
- Ignoring the flashing—many leaks come from flashing, not the skylight unit.
- Over-tightening screws or nails, which can crack the skylight frame.
- Not testing with water before closing up the ceiling.
Tips
- Work on a dry day with temperatures above 50°F (10°C) so sealant cures properly.
- If the skylight is old and the sealant is repeatedly failing, consider replacing the entire skylight unit—it may be more cost-effective in the long run.
- Use a ladder stabilizer or have someone hold the ladder base for safety.
- Take photos of the skylight and roof before and after repair for your records.
- Check the manufacturer’s warranty—some skylights have sealed units that shouldn’t be opened.
Troubleshooting
- Leak persists after resealing: The water may be entering from a different location, such as a roof valley or chimney, and traveling along the roof deck to the skylight. Inspect the entire roof slope above the skylight.
- Water appears only during heavy rain: This suggests a flashing issue rather than a seal issue. Check the flashing more thoroughly, especially the top and side pieces.
- Condensation inside the skylight: This is not a leak—it’s moisture in the air. Improve ventilation or use a dehumidifier. If the glass is double-paned and foggy, the seal has failed and the unit needs replacement.
- Sealant won’t stick: The surface may be too cold or damp. Warm the surface with a heat gun (careful not to damage shingles) and dry thoroughly before applying.
- You can’t reach the skylight safely: Call a professional roofer. Don’t risk injury on a steep or high roof.
Frequently Asked Questions
How often should I inspect my skylight?
At least twice a year, ideally in spring and autumn, and after severe storms.
Can I use silicone caulk to fix a leaking skylight?
Yes, but only exterior-grade silicone designed for roofing. Regular indoor silicone will break down quickly.
Do I need to replace the whole skylight if it leaks?
Not usually. Most leaks are from flashing or seals, which can be repaired. If the glass is cracked or the frame is warped, replacement may be needed.
Why does my skylight leak only when it rains hard?
Heavy rain can overwhelm the flashing or expose small gaps that light rain doesn’t reach. Inspect the flashing and seals for any gaps.
Can I repair a skylight from the inside?
You can apply sealant from inside if the leak is around the frame, but the actual problem is usually on the roof. For a lasting fix, work from the outside.
Is it safe to walk on my roof to fix the skylight?
Only if the roof is dry, not steep, and you have proper safety equipment. If in doubt, hire a professional.
Related
- How to Fix a Leaking Garden Faucet
- How to Shrink Margins in Word: Step-by-Step
- How to Fix a Leaking Garbage Disposal
Sources: Velux. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.