Home life · Updated
How to Fix a Leaking Garden Faucet
Quick answer Fix a leaking garden faucet by replacing the rubber washer or O-ring inside the handle, or tightening the packing nut. This stops drips and saves water.
Before you start, shut off the water supply to the faucet. Look for a shut-off valve on the pipe leading to the faucet, usually inside the house or near the exterior wall. If there isn’t one, you may need to turn off the main water valve. Open the faucet to drain remaining water and relieve pressure.
What You’ll Need
- Adjustable wrench
- Flathead screwdriver
- Replacement rubber washer (size matches your faucet)
- Replacement O-ring (if your faucet uses one)
- Plumber’s tape (thread seal tape)
- Bucket or rag (to catch drips)
Step-by-Step
- Turn off the water supply. Locate the shut-off valve for the faucet and turn it clockwise to close. If there’s no dedicated valve, shut off the main water supply to your home.
- Open the faucet to drain. Turn the handle to the open position and let any remaining water flow out. Keep it open while you work.
- Remove the handle screw. Look for a small screw on top of the handle or behind it. Use a flathead screwdriver to remove it. Some handles have a decorative cap that pops off to reveal the screw.
- Pull off the handle. Grip the handle firmly and pull it straight off the stem. If it’s stuck, gently rock it back and forth while pulling. Do not use excessive force that could break the stem.
- Loosen the packing nut. Use an adjustable wrench to turn the packing nut (the large nut just below the handle) counterclockwise. This nut holds the stem in place. You may need to hold the faucet body with another wrench to prevent it from turning.
- Remove the stem and replace the washer. Pull the stem out of the faucet body. At the bottom of the stem, you’ll see a brass screw holding a rubber washer. Remove the screw and the old washer, then install the new washer and secure it with the screw. If your faucet has an O-ring on the stem, replace that as well.
- Apply plumber’s tape and reassemble. Wrap a few layers of plumber’s tape clockwise around the threads of the stem (if it has threads). Insert the stem back into the faucet body, tighten the packing nut snugly with the wrench, then reattach the handle and tighten the screw.
- Turn the water back on and test. Close the faucet handle, then turn on the water supply. Open the faucet fully, then close it and check for leaks at the spout and around the handle. If it still drips, you may need to tighten the packing nut slightly more.
Common Mistakes
- Not turning off the water supply first, leading to a mess or injury.
- Using the wrong size washer, which doesn’t create a proper seal.
- Over-tightening the packing nut, which can crack the faucet body or strip threads.
- Forgetting to replace the O-ring if the faucet has one, causing leaks from the handle area.
- Not draining the line, so water sprays out when you remove the stem.
Tips
- Take the old washer with you to the hardware store to match the size exactly.
- Use a penetrating oil (like WD-40) on stubborn nuts and screws, but avoid getting it on rubber parts.
- If the faucet body is cracked or heavily corroded, replacement is safer than repair.
- Consider installing a frost-proof faucet if you live in a cold climate, to prevent future leaks.
- Check the washer annually and replace it proactively to avoid leaks.
Troubleshooting
- Faucet still drips after replacing the washer: The washer may be the wrong size or not seated properly. Disassemble and check. Also, inspect the seat (the metal surface the washer presses against) for nicks or corrosion; you may need a seat wrench to smooth it or replace the seat.
- Water leaks from around the handle: This is usually a worn O-ring or loose packing nut. Tighten the packing nut slightly, but if that doesn’t work, replace the O-ring on the stem.
- Handle is hard to turn after reassembly: The packing nut may be too tight. Loosen it a quarter turn and test. Also, ensure the stem is aligned properly.
- Water spurts from the spout when turned on: This could mean the washer is not sealing at all. Turn off water, disassemble, and check that the washer is installed correctly and the screw is tight.
- Can’t remove the handle: Use a puller tool or gently tap the handle with a hammer to break the corrosion. Avoid hitting the stem directly.
Frequently Asked Questions
Why is my garden faucet leaking at the handle?
This usually means the O-ring around the stem is worn. Replacing the O-ring should stop the leak.
Can I fix a leaking faucet without turning off the water?
No, you must turn off the water supply. Otherwise, water will spray out when you remove the stem, causing a flood.
What if my faucet doesn’t have a screw on the handle?
Some handles have a set screw on the side or a hidden screw under a cap. Look for a small hole or pry off a decorative cap with a flathead screwdriver.
How often should I replace the washer?
It depends on usage, but checking annually and replacing when you notice drips is a good rule. Hard water can wear washers faster.
Is it worth repairing an old faucet, or should I replace it?
If the faucet body is in good condition, replacing the washer is a cheap and easy fix. If the body is cracked or severely corroded, replacement is more reliable.
What is a frost-proof faucet, and does it leak differently?
A frost-proof faucet has a long stem that shuts off water inside the house. It can leak from the vacuum breaker or the packing nut, but the repair process is similar.
Related
- How to Fix a Leaking Faucet Handle
- Shrink SQL Server Log File: Step-by-Step Guide
- Fix a Leaking Faucet: Step-by-Step Guide
Sources: EPA WaterSense. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.