Home life · Updated
How to Tie an Anchor Hitch (Step-by-Step)
Quick answer An anchor hitch (also called a fisherman's bend) secures a rope to a ring, post, or anchor, and it holds fast under steady or jerking loads.
What You’ll Need
- A rope (any diameter, but thicker rope makes the knot easier to see)
- An anchor ring, a post, or a fixed object to tie around
- Optional: a second rope or a stick to practice the knot before using it in real conditions
Step-by-Step
- Pass the rope through the ring. Take the working end of your rope and pass it through the ring or around the post from underneath. Leave about 12–18 inches (30–45 cm) of working end beyond the ring.
- Wrap around the standing part. Bring the working end around the standing part (the long, load-bearing side of the rope) once, making a full loop around it.
- Wrap a second time. Wrap the working end around the standing part a second time, in the same direction, so you have two parallel turns around the standing part.
- Pass the working end back through the loops. Take the working end and tuck it under both wraps you just made, going in the same direction as the wraps. This creates a simple hitch around the standing part.
- Pull the knot tight. Hold the standing part and pull the working end to snug the wraps against the ring. Then pull the standing part firmly to seat the knot.
- Finish with a half hitch (optional but recommended). To make the knot extra secure, tie a half hitch around the standing part with the remaining working end, about an inch away from the main knot. This acts as a backup and keeps the anchor hitch from slipping.
Common Mistakes
- Only one wrap instead of two: The anchor hitch relies on two wraps around the standing part. A single wrap can slip under a heavy load.
- Wrapping in opposite directions: If you wrap once clockwise and once counterclockwise, the wraps cross and the knot becomes unstable. Keep both wraps in the same direction.
- Not pulling the knot tight before loading: A loose anchor hitch can work itself loose. Always snug it up before applying load.
- Skipping the backup half hitch: Without the backup, the knot can still come undone if the rope is very slippery or the load jerks. The half hitch is cheap insurance.
Tips
- Practice with a thick rope first so you can clearly see the wraps and tucks.
- Wet or icy rope can make the knot harder to tie and more prone to slipping—add an extra half hitch in those conditions.
- When tying around a post, make sure the standing part runs away from the post in a straight line, not at an angle, so the knot seats properly.
- If you need to untie it later, the anchor hitch is relatively easy to undo, but it can jam under heavy load. Leave a longer working end if you think you’ll need to untie it quickly.
Troubleshooting
Knot slips or comes undone: Check that you made two full wraps and that they are parallel. If the rope is very smooth (like nylon), add a third wrap or an extra half hitch.
Knot jams and won’t untie: This happens when the load is very heavy. Try to loosen the knot by wiggling the wraps, or use a marlinspike (a pointed tool) to pry the wraps apart. If you can’t untie it, cut the rope—but that’s a last resort.
Wraps look crossed or messy: Undo the knot and start again. Make sure you wrap the working end around the standing part in the same direction each time, and keep the wraps neat and close together.
Knot won’t stay tight before loading: Pull on the standing part while holding the wraps with your other hand. This seats the knot and prevents it from loosening while you tie the backup half hitch.
Frequently Asked Questions
Is an anchor hitch the same as a fisherman’s bend?
Yes, the anchor hitch is commonly called a fisherman’s bend. It’s the same knot.
Can I use an anchor hitch to tie a rope to a carabiner?
Yes, but a carabiner is usually better suited for a clove hitch or a girth hitch. The anchor hitch works fine on a carabiner, but the ring shape may make the knot less secure because the wraps can slide.
How strong is an anchor hitch compared to other knots?
It’s very strong and holds well under load, but it does weaken the rope somewhat, like any knot. It’s considered reliable for most applications, but for critical life-safety situations, use a knot specifically rated for that purpose.
Why does my anchor hitch keep slipping on a smooth post?
On a smooth post, the friction is lower. Make sure you have two full wraps around the standing part, and add a backup half hitch. You can also try a different knot like a rolling hitch for extra grip.
Can I tie an anchor hitch with a rope that’s too short?
You need enough working end to make the wraps and the backup half hitch. If the rope is too short, you won’t be able to complete the knot properly. Use a longer rope or a different knot that requires less length.
What’s the difference between an anchor hitch and a clove hitch?
A clove hitch is tied around an object itself, while an anchor hitch is tied around the standing part of the rope. The anchor hitch is generally more secure under a steady pull.
Related
- Remove Peacock Continue Watching Step-by-Step
- How to Organize Tabs in Excel: Step-by-Step Guide
- How to Organize Rows in Excel by Date
Sources: Animated Knots by Grog. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.