AjapaReporter

Home life · Updated

How to Fix a Leaking Toilet Cistern

Time it takes45 min
Steps8in the list below
LevelEasyno special skills
Official sourceUK Water Regulationscheck it for changes

Quick answer To fix a leaking toilet cistern, identify the leak source (inlet valve, outlet valve, or tank cracks), then replace or adjust the faulty part. Most leaks are fixed in under an hour with basic tools.

What You’ll Need

  • Adjustable wrench or pliers
  • Screwdriver (flathead and Phillips)
  • Sponge or towel
  • Bucket or container
  • Replacement parts: flapper, fill valve, or cistern washer (as needed)
  • Plumber’s tape (optional)
  • Safety gloves

Step-by-Step

  1. Turn off the water supply. Locate the shut-off valve on the wall behind the toilet and turn it clockwise until it stops. Flush the toilet to drain most of the water from the cistern.
  2. Remove the cistern lid. Lift the lid carefully and set it aside on a flat surface. Check the inside for any obvious signs of water dripping or pooling.
  3. Identify the leak type. Dry the inside of the cistern with a sponge. Look for water flowing continuously into the overflow pipe (a tube in the center) or dripping from the flush valve at the bottom. Also check the base of the cistern for cracks.
  4. Fix a running inlet valve. If water constantly runs, the fill valve is likely faulty. Adjust the float arm if it’s bent, or replace the valve: unscrew the locknut under the cistern, lift out the old valve, and install the new one per the manufacturer’s instructions.
  5. Replace a worn flapper or flush valve. If water leaks from the cistern into the bowl, the flapper (or flush valve seal) is worn. Remove the old flapper by unhooking it from the chain and lift arms, then attach a new one. For a full flush valve replacement, drain the cistern completely, unscrew the locknut, and swap the entire unit.
  6. Tighten loose connections. Use an adjustable wrench to gently tighten the nuts securing the water supply line and the cistern to the bowl. Avoid overtightening—this can crack the porcelain.
  7. Check for cracks in the cistern. If you see a hairline crack, the cistern may need to be replaced. As a temporary fix, you can apply silicone sealant, but this is not a permanent solution.
  8. Turn the water back on and test. Open the shut-off valve slowly, let the cistern fill, and flush a few times. Check for drips around the base and inside the bowl. Wipe everything dry and re-check after a few minutes.

Common Mistakes

  • Not turning off the water supply before starting—this can cause a flood.
  • Overtightening nuts, which can crack the ceramic cistern.
  • Replacing the flapper but leaving the chain too tight or too loose, causing it to not seal properly.
  • Ignoring a leaking inlet valve and only adjusting the float, when the valve itself needs replacement.
  • Using the wrong replacement part—always check the model number or bring the old part to the hardware store.

Tips

  • Before buying parts, take a photo of the inside of your cistern to help match the correct flapper or valve.
  • Apply a thin layer of plumber’s grease to rubber seals to help them last longer and seal better.
  • If the flapper chain has extra links, shorten it so there’s about 1/4 inch of slack when the flapper is closed.
  • Clean the cistern interior gently with a cloth and mild soap—abrasive cleaners can damage seals.
  • Test for leaks by adding a few drops of food coloring to the cistern; if color appears in the bowl without flushing, you have a leak.

Troubleshooting

  • Water still runs after replacing the flapper. The flapper may not be seating properly—check if the chain is too tight or if the flapper is warped. Also ensure the flush valve seat is clean and smooth.
  • Leak at the base of the cistern. This is usually a worn or misaligned rubber gasket between the cistern and bowl. Drain the cistern, remove the bolts, and replace the gasket.
  • Water drips from the inlet valve top. The valve may have a cracked body or a faulty diaphragm. If adjusting the float doesn’t help, replace the entire fill valve.
  • Hissing noise after filling. This often means the fill valve is not fully closing. Adjust the float so the water shuts off at a lower level, or clean the valve’s inlet screen.
  • Cistern fills too slowly. Check if the shut-off valve is fully open, and clean any debris from the fill valve’s inlet filter.

Frequently Asked Questions

Why does my toilet cistern leak only sometimes?

Intermittent leaks often happen when the flapper gets stuck open due to chain misalignment, or when the fill valve’s float is slightly off, causing occasional overflows.

Can I fix a cracked cistern with sealant?

Silicone sealant can be a temporary stopgap, but a cracked cistern is structurally weak and may worsen. Replacing the cistern is the safe, permanent fix.

How do I know if I need a new flapper or a new flush valve?

If the flapper is visibly warped, cracked, or no longer sits flat, replace it first. If the leak persists, the flush valve’s seat may be corroded, requiring a full valve replacement.

Is it normal for the cistern to sweat?

Sweating is condensation, not a leak. It happens when cold water meets warm, humid air. Insulating the cistern or reducing humidity can help, but it’s not a plumbing issue.

What if the leak is at the water supply line connection?

Tighten the nut gently. If it still leaks, replace the rubber washer inside the supply line’s connector or wrap plumber’s tape around the threads before reconnecting.

Do I need a plumber for a cistern leak?

Most cistern leaks are DIY-friendly. However, if you encounter a cracked cistern, inaccessible shut-off valve, or persistent leaks after replacing parts, call a plumber.

Sources: UK Water Regulations. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.