Home life · Updated
How to Fix a Leaking Toilet Tank
Quick answer To fix a leaking toilet tank, first identify the leak source—usually the tank-to-bowl gasket, fill valve, or flush valve—then replace the faulty part. Most leaks are fixed in under an hour with basic tools.
What You’ll Need
- Adjustable wrench
- Slotted and Phillips screwdrivers
- Sponge or towel
- Bucket
- Replacement parts (tank-to-bowl gasket, fill valve, or flush valve, depending on the leak)
- Plumber’s tape (optional, for threaded connections)
Step-by-Step
- Turn off the water supply. Locate the shut-off valve on the wall behind the toilet and turn it clockwise until it stops. Flush the toilet to empty the tank, then sponge out any remaining water.
- Inspect the tank exterior. Wipe the tank dry with a towel. Look for water dripping from the tank onto the floor or down the sides. This helps pinpoint the leak location before disassembly.
- Check the tank-to-bowl gasket. If water leaks from the bottom of the tank where it meets the bowl, the large rubber gasket between them is likely worn. Remove the tank by unscrewing the two bolts inside the tank (use a wrench on the nuts underneath) and lifting it straight up. Replace the gasket, then reseat the tank.
- Inspect the flush valve. If water leaks continuously into the bowl (you hear a hissing sound), the flapper or flush valve seat may be warped or dirty. Remove the tank lid, then lift the flapper to check for debris or wear. Clean the seat with a cloth, or replace the flapper if it’s cracked.
- Test the fill valve. If water leaks from the top of the fill valve or drips down the overflow tube, the fill valve is faulty. Turn off the water, disconnect the supply line, and unscrew the fill valve from the bottom of the tank. Install a new one, adjusting its height so the water level sits about 1 inch below the overflow tube.
- Reassemble and tighten connections. After replacing any part, reattach the tank to the bowl (if removed), hand-tighten the bolts, then snug them with a wrench—but don’t overtighten, as this can crack the porcelain. Reconnect the supply line.
- Turn the water back on. Open the shut-off valve slowly. Watch the tank fill and check for leaks at the base, the supply line, and around the fill valve.
- Flush and observe. Flush the toilet several times. Look for drips on the floor, around the tank bolts, and at the base of the bowl. Also check that the flapper closes fully and the tank refills to the correct level.
- Dry and verify. Wipe all surfaces dry, then wait 10–15 minutes. Recheck for any new moisture. If everything stays dry, the leak is fixed.
Common Mistakes
- Overtightening bolts—this can crack the tank or bowl, causing a worse leak.
- Forgetting to clean the sealing surface—old gasket residue prevents a watertight seal.
- Reusing a worn flapper—if it’s warped or has mineral buildup, it won’t seal.
- Misaligning the tank—when reinstalling, the tank must sit level and centered on the bowl.
- Skipping the supply line check—a loose or cracked supply line can leak even if the tank parts are fine.
Tips
- Use a mirror to inspect the underside of the tank for hard-to-see drips.
- Add a few drops of food coloring to the tank; if color appears in the bowl without flushing, the flapper is leaking.
- Apply plumber’s tape to threaded connections for a better seal.
- Keep the tank lid off while testing to make adjustments easier.
- If you’re unsure which part is faulty, replace the flapper first—it’s the most common cause of a leaking tank.
Troubleshooting
- Leak persists after replacing the gasket: The tank may be cracked. Run a finger along the inside bottom edge—if you feel a crack, the tank needs replacement.
- Water leaks from the base of the toilet (not the tank): This is a wax ring issue, not a tank leak. You’ll need to remove the toilet to replace the wax ring.
- Supply line leaks at the connection: Tighten the nut slightly, or replace the supply line if it’s corroded.
- Fill valve runs continuously: Adjust the float arm or replace the valve if adjustment doesn’t stop the flow.
- Bolts at the tank base are corroded: Replace them with new brass bolts and rubber washers.
Frequently Asked Questions
Why is my toilet tank leaking from the bottom?
Usually the tank-to-bowl gasket is worn or the tank bolts are loose. Remove the tank, replace the gasket, and tighten the bolts evenly.
Can I fix a leaking tank without removing it?
If the leak is from the flapper or fill valve, yes—just open the tank and replace those parts. If it’s from the base, you must remove the tank to access the gasket.
How do I know if the flapper needs replacing?
If water continuously runs into the bowl, or the flapper looks warped, cracked, or has mineral buildup, replace it. A food coloring test can confirm a slow leak.
What if the tank is cracked?
A cracked tank cannot be reliably repaired; you need to replace the entire tank or toilet. Look for hairline cracks near the bolts or along the bottom.
Is it normal for the tank to sweat?
Yes, in humid conditions, condensation can form on the outside of the tank. This isn’t a leak; it’s moisture from the air. Insulating the tank or reducing humidity helps.
How often should I replace the flapper?
Every few years, or as soon as you notice a leak. Flappers degrade with water chemicals and use.
Related
- How to Remove Stains from an Iron Soleplate
- How to Phone Barclays: UK Customer Service Numbers
- How to Remove Stains from an Iron Bottom
Sources: EPA WaterSense. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.