Home life · Updated
How to Fix a Leaking Shower Head
Quick answer Fix a leaking shower head by checking the washer, tightening connections, and clearing mineral buildup. Most leaks stop with a new rubber washer or plumber's tape.
What You’ll Need
- Adjustable wrench or pliers
- Plumber’s tape (PTFE tape)
- Replacement rubber washer (size matches your shower head)
- White vinegar (for mineral buildup)
- Small brush or old toothbrush
- Bucket or towel
- Rubber gloves (optional)
Step-by-Step
- Turn off the water supply. Locate the shut-off valve for the shower, usually behind an access panel or near the water heater. Turn it clockwise to close. If there’s no dedicated valve, turn off the main water supply to the house.
- Release remaining water pressure. Turn the shower handle to the full hot position and let any water drain out into a bucket or towel. This prevents water from spraying when you loosen the head.
- Remove the shower head. Use an adjustable wrench or pliers to grip the nut connecting the shower head to the pipe. Turn counterclockwise. If it’s stuck, wrap the nut with a cloth to avoid scratches, then gently tap with a wrench handle. Unscrew completely and set the head aside.
- Inspect the washer and threads. Look at the rubber washer inside the shower head’s connection. If it’s cracked, flattened, or worn, replace it with a new one. Also check the threads on both the pipe and the head for damage or mineral deposits.
- Clean the shower head (if needed). If you see white or green buildup, soak the shower head in white vinegar for 30 minutes to an hour. Use a small brush to remove loose debris from the nozzles. Rinse thoroughly with water.
- Apply plumber’s tape. Wrap plumber’s tape clockwise around the pipe threads, 2-3 times. Ensure it’s snug but not overlapping too thick. This creates a watertight seal.
- Reattach the shower head. Screw the shower head back onto the pipe by hand, turning clockwise. Tighten with a wrench an additional quarter-turn, but don’t overtighten—this can crack the head or strip threads. Turn the water back on and test for leaks.
Common Mistakes
- Overtightening: Using too much force can crack the shower head or damage the pipe threads. Tighten only until snug, then a slight extra turn.
- Wrong washer size: Using a washer that’s too small or too large won’t seal properly. Match the old washer’s diameter.
- Forgetting plumber’s tape: Skipping tape on metal-to-metal connections often leaves a small gap that drips.
- Not cleaning mineral buildup: If the head is clogged, water may leak from the connection due to back pressure. Clean the nozzles first.
- Turning on water too quickly: Sudden pressure can dislodge a new washer. Turn on slowly and check for drips.
Tips
- Use a rubber strap wrench for a better grip without scratching chrome or plastic.
- Apply a small amount of plumber’s grease to the washer to help it seat properly.
- If your shower head has a swivel ball joint, check that the O-ring inside is intact—replace if worn.
- For stubborn mineral deposits, soak the head in a 50/50 vinegar-water solution overnight.
- Keep a spare washer and tape in your bathroom for quick fixes.
Troubleshooting
- Leak persists after replacement: Check if the pipe threads are cracked or corroded. If so, you may need to replace the pipe or use a thread sealant compound.
- Water sprays from the side of the head: This usually means the washer is misaligned or the tape is too thick. Remove, re-seat the washer, and reapply tape thinly.
- Shower head is hard to remove: Apply penetrating oil to the threads and wait 10 minutes. Then try tapping gently with a wrench. If still stuck, call a plumber.
- Leak comes from the wall, not the head: If water drips behind the plate, the pipe connection inside the wall is leaking. Turn off water and tighten the nut behind the plate, or replace the pipe if needed.
- New head leaks at the hose (handheld type): Check the rubber gasket inside the hose connector and replace if damaged. Also ensure the hose is fully screwed in.
Frequently Asked Questions
Why does my shower head leak even when the tap is off?
This is usually a worn washer or a loose connection. The washer may not be sealing fully, allowing water to seep past. Replace the washer and tighten the connection.
Can I fix a leaking shower head without removing it?
Sometimes. If the leak is at the connection, you can try tightening the nut with a wrench. If it’s from the head itself, you may need to clean the nozzles with vinegar, but removing is more effective for a full fix.
How do I know if I need plumber’s tape?
If the threads are metal and you see water dripping from the connection, tape is recommended. For plastic threads, tape is often unnecessary but can still help.
What if the washer looks fine but it still leaks?
Check the pipe threads for damage or debris. Clean them with a wire brush and apply fresh tape. Also inspect the shower head’s seat—it may be cracked.
Is it safe to use vinegar on all shower heads?
Vinegar is safe for metal and most plastic heads, but avoid it on specialty finishes like gold or painted surfaces. For those, use a mild soap solution instead.
How often should I replace the washer in my shower head?
There’s no set schedule. Replace it when you notice a leak or when it looks worn during cleaning. Regular inspection every few months can help.
Related
- How to Use Android on PC: Full Guide
- How to Wash a WHOOP Band: Step-by-Step Guide
- How to Wash White Clothes: A Complete Guide
Sources: EPA WaterSense. Menus and buttons can differ slightly by version. Spotted something out of date? Tell us.